This document provides a step by step installation of ETAP 5.5.6 License Manager, which is required for USB Key – ETAP-OTI 1410 and Parallel Port Key.   To install the network version of ETAP you need to install the ETAP 5.5.6 License Manager as provided in the enclosed ETAP 5.5.6 August 2007 CD.  

After installation, ETAP 5.5.6 may prompt you for an Activation Code the first time you run the software. This 36-character activation code is located on the ETAP CD sleeve. If you are upgrading from the previous release of ETAP, the activation code can be found on your existing ETAP 5.5.6 CD sleeve.

Installation of the ETAP License Manager 5.5.6 is required for the following licenses:

1. ETAP Network License, using parallel port or any ETAP USB keys.
2. ETAP Stand Alone License, using the USB Key – ETAP-OTI 1600.

A label on the key identifies the key as “Stand Alone” or “Network”.  For the Network license, the License Manager and key are installed on a server PC and ETAP is installed on the client PC.  However, the Network license has the option to install ETAP, License Manager, and key on the same PC.  For the Stand Alone license, the ETAP application, the License Manager, and key must be installed on the same PC. 

To continue with the installation instructions, first identify the type of license you are using.

1. Are you using a Network or Stand Alone key?  A label on the key identifies the key as “Stand Alone” or “Network”.
2. Are you using a USB Key – ETAP-OTI 1410 or a Parallel Port Key?  Identify the type of key you are using by referring to the pictures shown below.

• ETAP
• ETAP Real-Time Server
• ETAP License Manager

Previous versions of the ETAP License Manager will be detected by the install and should be uninstalled from the Add/Remove Programs control panel (Figure 1).

If necessary, this message can be bypassed by running the Setup from the Run command and using the /z”force” command (Figure 2).  The example below assumes the D: drive is the CD ROM.

Figure 2

ETAP Setup displays the ETAP License Manager Welcome dialog box for version 5.5.6.  Click the Next button to continue.  Be sure to remove any ETAP hardware keys from the computer.

The ETAP License Agreement is displayed.  By clicking Yes you accept the terms of the Agreement.

The Setup displays the default path to install the ETAP License Manager. Click Browse to select a different path or click Next to continue.

The Setup has enough information to begin the installation.  Click Next to begin the file transfer.

The Setup will attempt to start the ETAP License Manager (referred to in the Services control panel as Etaps Lic Mgr).  This process may take a few seconds.

The Setup is complete if the service starts successfully.  No reboot of the PC is necessary.

Installation on Windows 2000/XP or Server 2003 must be performed by a user with Administrative privileges. Use the manual installation only if the ETAP License Manager Installation Program did not successfully install the ETAP License Manager.

Note: Substitute your Windows NT folder name (usually WINNT or Windows) whenever you see WINNT in this document.

2.1 Logon with administrator privileges to the computer acting as the License Manager server.

2.2 It is necessary to remove an older version of the ETAP License Manager before installing a new one. Remove the old one from the Add/Remove Programs in the Control Panel. It is best to restart the computer after uninstalling the program. Continue with #2.3 after restarting.

2.3 From the ETAP CD subfolder LMSETUP\SYSTEM32\DRIVERS, copy the following files into the WINNT\SYSTEM32\DRIVERS subfolder on the hard disk:

2.4 From the WINNT\SYSTEM32\DRIVERS subfolder on the hard disk run ETAPKEY.EXE.

2.5 From the ETAP Key menu, select Install ETAP Key and then exit from ETAPKEY.

2.6 From an MS-DOS prompt, go to the WINNT\SYSTEM32\DRIVERS subfolder.

2.7 Type: etapslmt –install (for TCP/IP). You should see a message that says: ETAPS Lic Mgr installed.

2.8 Restart the License Manager server.